Calculating the hardness of the material is straightforward using the above mentioned formula, and the Vickers hardness is expressed in this form xxxHVyy or xxxHVyy/zz. Where xxx stands for the Vickers hardness number, yy is the load, and zz is if the dwell time is beyond the approved standard of 10 to 15 seconds. For example, the load applied ranges between 1 gf to 120 kgf, which depends on the material being tested. The indenter must contact the specimen at a controlled velocity between 15 and 70 μm/s, not exceeding 0.2 mm/s.

• Vickers by Danfoss industrial valves give you their best day in, day out, in both stationary and mobile hydraulic applications.

{

• 1929 saw the merger of the acquired railway business with those of Cammell Laird to form Metropolitan Cammell Carriage & Wagon.

|}{

• In 1921, the Vickers Hardness Test was developed by Robert L. Smith and George E. Sandland at Vickers Ltd.

|}

• The average of the diagonal measurements is taken to get the single value to be used in the Vickers hardness test formula.

{

• Industrial applications require industrial-strength hydraulic systems—like those built with Danfoss piston pumps.

|}

• In 1928, the Aviation Department became Vickers (Aviation) Ltd and soon after acquired Supermarine, which became the “Supermarine Aviation Works (Vickers) Ltd”.

The hardness number is determined by the load over the surface area of the indentation and not the area normal to the force, and is therefore not pressure. The load is applied for a standard period of about 10 to 15 seconds, and the two diagonals of the indentation created are measured using a microscope. The hardness of a material can also be expressed in terms of the load used, for example, HV5 means the hardness calculated for a 5kg load.

• For example, the load applied ranges between 1 gf to 120 kgf, which depends on the material being tested.

{

• In 1927, Vickers merged with Tyneside based engineering company Armstrong Whitworth to become Vickers-Armstrongs.

|}{

• The load is applied for a standard period of about 10 to 15 seconds, and the two diagonals of the indentation created are measured using a microscope.

|}{

• The indentation made by using the indenter must have a properly defined shape to be able to be measured.

|}

• The hardness of a material can also be expressed in terms of the load used, for example, HV5 means the hardness calculated for a 5kg load.
• In the world of materials science and metallurgy, Vickers Hardness Test is one of the processes used to determine material hardness.

Applications of Vickers Hardness Test

Armstrongs shipbuilding interests became the “Naval Yard”, those of Vickers on the west coast the “Naval Construction Yard”. The company went public in 1867 as Vickers, Sons & Company and gradually acquired more businesses, branching out into various sectors.

Download PM Material Comparison Table

Among all hardness testing methods, the Vickers test is preferred for sintered metal due to its precision and adaptability. This allows for accurate measurement of the matrix hardness while minimizing errors caused by surface porosity. Industrial applications require industrial-strength hydraulic systems—like those built with Danfoss piston pumps. A Vickers hardness tester is the ideal solution for precision hardness measurement of small, thin, or delicate materials.

Why Choose a Vickers Hardness Tester?

{

• The Vickers name lived on in Alvis Vickers, until the latter was acquired by BAE Systems in 2004 to form BAE Systems Land Systems.
• The unit of hardness given by the test is known as the Vickers Pyramid Number (HV) or Diamond Pyramid Hardness (DPH).

{

• In 1960, the aircraft interests were merged with those of the Bristol, English Electric and Hunting Aircraft to form the British Aircraft Corporation (BAC).

|}{

• A Vickers hardness tester is used to measure the hardness of materials by applying a pyramid-shaped diamond indenter under a controlled force.

|}

• This indenter is applied onto the surface of the test material with force from a load, which ranges from a few grams to 100 kgf.

{

• A Vickers hardness tester is the ideal solution for precision hardness measurement of small, thin, or delicate materials.

|}

|}
The Vickers test method involves pressing the indenter into the test material and measuring the diagonal lengths of the indentation left after the load is removed. The basic principle, as with all common measures of hardness, is to observe a material’s ability to resist plastic deformation from a standard source. The unit of hardness given by the test is known as the Vickers Pyramid Number (HV) or Diamond Pyramid Hardness (DPH). The hardness number can be converted into units of pascals, but should not be confused with pressure, which uses the same units.

Industrial Valves

The indentation made by using the indenter must have a properly defined shape to be Vickers able to be measured. The indenter is used to apply the load to the test sample for a dwell time of about 10 to 15 seconds. The Vickers test follows standards such as ASTM E384 or ISO 6507, and can be very useful for comparative studies. In 1921, the Vickers Hardness Test was developed by Robert L. Smith and George E. Sandland at Vickers Ltd. Vickers Hydraulic Valves are available with or without integral relief valve section and are suitable for pressures up to 3000 psi.

Vickers Hardness Testers for Precise and Versatile Applications

The Vickers hardness test is ideal for evaluating very small areas, thin materials, and coatings with high accuracy. With innovations spanning from alternative energy and civil engineering to manufacturing and marine, we’re one of the world’s most trusted industrial hydraulic solution partners. As a worldwide leader, Vickers Hydraulics designs and manufactures a comprehensive line of reliable, high-efficiency hydraulic systems and components. In 1960, the aircraft interests were merged with those of the Bristol, English Electric and Hunting Aircraft to form the British Aircraft Corporation (BAC). This was owned by Vickers, English Electric and Bristol (holding 40%, 40% and 20% respectively). The Supermarine operation was closed in 1963 and the Vickers name for aircraft was dropped in 1965.
{

Conversion to SI units

|}
Elevate your systems to new heights with the unmatched power and precision of Vickers hydraulic solutions. The average of the diagonal measurements is taken to get the single value to be used in the Vickers hardness test formula. In the world of materials science and metallurgy, Vickers Hardness Test is one of the processes used to determine material hardness. Hardness testing generally aids engineers in assessing the strength, durability, and wear resistance of a material. Vickers by Danfoss industrial valves give you their best day in, day out, in both stationary and mobile hydraulic applications. Vickers®, one of the most experienced and respected names in hydraulics, became part of Danfoss in 2021.
Embark on a journey to the core of hydraulic systems, where the heartbeat is the pump. These pumps go beyond expectations, providing the reliability and efficiency demanded by your operations. Vickers Pumps by Danfoss are known for their precision, reliability, and efficiency in fluid power applications. The Vickers brand carries a legacy of excellence in delivering high-performance hydraulic components. Yes, the Vickers hardness rating of a material is inversely proportional to the indentation size.
{

Applications

|}
In 1929, the acquired railway business was merged with that of Cammell Laird to form Metropolitan Cammell Carriage & Wagon. In 1928, the Aviation Department became Vickers (Aviation) Ltd and soon after acquired Supermarine, which became the “Supermarine Aviation Works (Vickers) Ltd”. 1929 saw the merger of the acquired railway business with those of Cammell Laird to form Metropolitan Cammell Carriage & Wagon. In 1927, Vickers merged with Tyneside based engineering company Armstrong Whitworth to become Vickers-Armstrongs.